How to make an antenna with your own hands for a TV: simple ideas

Tags:With your own hands

In the modern world, there is a significant range of high-tech and functional antennas for installation in the home. But there are times when the TV has ceased to be shown in a suburban home. Some craftsmen find a way out in this situation and make something that helps to correct the situation. Moreover, they give recommendations to others: how to make an antenna with your own hands for a TV. Let's take a look at some simple methods that you might find useful.

How to make an antenna with your own hands for a TV

Homemade devices are especially good when they are needed for temporary use.

The content of the article [Hide]

1 How to make an antenna with your own hands for a TV from beer cans
2 Is it possible to make a homemade antenna for digital television from wire
3 DIY antenna option for digital TV HDTV
4 The nuances of the apartment option
5 Helpful hints
6 How to make an antenna for a TV from scrap materials with your own hands (video)

How to make an antenna with your own hands for a TV from beer cans

The easiest and most unusual option to construct an antenna is from beer cans. And according to experts, as many as seven channels will be shown. To build a similar structure, prepare:

a couple of washed and dried beer cans;
a pair of self-tapping screws;
several meters of television cable;
soldering iron with tin;
screwdriver;
electrical tape.

When deciding how to make an antenna with your own hands for a TV, keep in mind that the gap between the end parts of the cans should be about 75 mm. And the best arrangement of the structure is near the windows.

Mounting options can vary greatly

The stick to be used for the antenna must be made of wood. You cannot take aluminum or titanium options. Parts of the cable can be soldered. Instead of tape, you can use duct tape or even a plaster. The containers for creating the device must be well rinsed and be sure to dry. To improve the image quality, you can play with the distance between the banks.

Table 1. Antenna from beer cans

Picture	Stages
	Prepare the cable. To do this, make a cut from one edge and remove the insulation layer. Then the middle layer is cut off. At the other end, a plug for the TV antenna is mounted.
	Stock up on banks. Their capacity should be 1 liter!
	Connect your contacts.One end of the twisted cable is mounted to the bank, and the other, with a copper core, to the other. Fastening is carried out using a screwdriver and a soldering iron.
	Assemble the antenna. A trempel is used as a carrier.
	Set up your device.

Related article:

Bracket for TV on the wall, sliding. In the article we will consider the features of the application, the types of the device, the secrets of selection and installation.

Is it possible to make a homemade antenna for digital television from wire

A good way is to use copper wire to create the antenna. For such a mechanism you will need an amplifier, wire, sheet of metal, drill, bolts, metal pipe, cable and hammer.

To make such a homemade home antenna for a TV, we do the following:

at the first stage we make a catcher. For its manufacture, the wire must be bent so that all sides have a length of 45 cm;
then we fix the wire on the plate. In this case, a connection is made to the plate;
the cable is connected;
a mast is made from a metal pipe. Its base must be buried.

The simplest construction is made from a piece of wire.

Helpful information! All details should be painted over. This will protect the product from corrosion and aggressive operating conditions.

DIY antenna option for digital TV HDTV

There are various methods to make your own TV antenna. The first two methods we have considered operate at a frequency of 270 MHz. And the next option has great possibilities. In this case, the picture will be of better quality, since the signal can reach 490 MHz. You will definitely need a special transformer, which is unlikely to be found among the materials at hand. Such a device must be purchased in advance. There are also methods for making a transformer yourself, but they are quite complicated. From the materials it is worth preparing cardboard, tape, foil, stapler, marker, tape measure and glue.

First, you should print a special diagram for installing such a device. All structural elements are cut out according to the scheme, as well as all the necessary parts from foil. Then you need to make a butterfly out of cardboard and paint over individual parts with a marker.
The next step is to build a reflector, the size of which is 35-32.5 cm. One side is glued with foil.
In the middle, rectangles of the same size are cut. They are needed to design a trap for construction. The length of the plate should be about 35 mm. This product is designed to - maintain the distance between additional elements and the reflector.
The individual parts are glued to the rectangular element. Then grooves are drilled for the cable.

How to make an antenna with your own hands for a TV, the correct instructions will tell you. The transformer is necessarily connected, and the cable is installed in the plug. This method is only suitable for indoor use, as the paper will quickly deteriorate outdoors.

The table details all stages of the installation of such equipment.

Table 2. DIY antenna for digital TV HDTV

Picture	Work stages
	Prepare the necessary material.
	Print the template and cut it out.
	Cut out the reflector from cardboard, and then glue it with foil.
	Cut out rectangles in the middle.
	Also, you need to cut out all the necessary parts from cardboard. This applies the template.
	It is better if you color all the details.
	Foil is also cut using stencils.
	To create a bend, a small undercut is made on the dotted line.
	Foil is glued to individual antenna elements.
	The antenna is being assembled. At the same time, measure 35 mm from the reflector and glue the butterfly.
	A hole is made in the middle of this element for the passage of the cable.
	A suitable transformer is installed and the antenna is ready.

Related article:

TV stand in modern style: photo. This article tells about what parameters a high-quality TV stand has, and photos and descriptions will help you choose the best option for your interior.

The nuances of the apartment option

In the manufacture of some types of structures, you can make an antenna amplifier with your own hands. Try to make a quality amplifier from scrap materials that can be used for both street and home use.

To carry out the work, the following materials will be required:

copper wire, which is 4 m long and about 4 mm in diameter;
board of any thickness with a width of 70 mm and a length of 550 mm;
self-tapping screws and screwdriver;
plug and soldering iron;
pencil and ruler.

An amplifier device is a complex design

Follow the drawing. First, drill holes in the surface. The parameters from the diagram are transferred to the board, and drilling is performed in certain places. Copper wire is measured and cut into 8 identical sections. In the middle of each section, you need to remove the insulation.

Cut two pieces and conditionally divide them into three parts, and remove the insulation layer at the fold points. In bare areas, you need to bend the wire. On these elements, the distance between the edges should be about 75 mm. This is the optimal distance for good signal reception. You need to attach the plug to the prepared homemade product, and then connect the cable to it. Then you need to find a suitable place to mount the device.

Helpful hints

If the receiver is at some distance from the generator, then its power decreases. To correct this defect, special amplifiers are used.To fix a homemade device, a special mast is required, which is performed on its own. In this case, steel pipes are useful.

Select two pipes and bury them in the ground. On the sides of the lines, it is necessary to drill recesses and install steel rods. Then a prepared pipe from a sleeve is put on them. With its help, you can mount a different number of pipes. Attach them with a special steel cable. By using additional pipes, you can all make the mast longer. It is not difficult to make such a structure.

It will take no more than 30 minutes to make some antenna options. This will create a mechanism for receiving the television signal.We hope that our instructions will help you make an antenna yourself. You can find many other interesting instructions. After all, a homemade structure can be made from electrodes, aluminum discs and copper tubes.